GT Products 2100 is a non-slump one-part silicone that cures to a tough elastomer when exposed to atmospheric moisture at room temperature. GT Products 2100 may be applied to horizontal, vertical and overhead surfaces without sagging. GT Products 2100 will adhere without a primer to many clean substrates such as aluminum, steel, glass, wood, silicone rubber, and many plastics.
FEATURES
GT Products 2100 features excellent resistance to heat, cold, water, ozone, and ultraviolet rays. It remains flexible and does not crack or harden. GT Products 2100 contains no solvents and has negligible shrinkage during cure; GT Products 2100 is useful over a temperature range of –75°F to 450°F for extended operation and for intermittent periods up to 500°F GT Products© 2100 meets the requirements of 21 CFR 177.2600: Mil A-46106A, TT-S001543A, TT-S-00230, ASTM- 920-79
As Supplied: Color white, clear, black, aluminum
| Specific Gravity | 1.04 |
| Extrusion Rate (1/8 in. | |
| orifice, 90 psi) | 350 gm/min. |
| Tack-free time | |
| (77°F ./. 50% RH) | 10 – 20 min. |
| Cure time 1/8 thickness | |
| (77°F / 50%RH) | 24 hr. |
| As Cured: | |
| Durometer (Shore A) | 30 |
| Tensile, psi: | 350 |
| Elongation, % | 500 |
| Brittle Point | -100°F |
| Volume Coefficient of |
Thermal Expansion, (32-212°F) 9.3x10-4 Thermal Conductivity CAL (cm) (C)(sec) 4.5x10-5
BTU (ft) (F) (hr) 0.11 Volume Resistivity, ohm-cm 1.5x1015 Dielectric Strength, volt/mil 550 Dielectric Constant,
60 Hz 2.8 100 KHz 2.8 Dissipation Factor 60 Hz 0.0015 100 KHz 0.0015
GT Products 2100 will adhere to most clean surfaces without additional preparation. Mild abrasion of rubber surfaces will usually improve adhesion. A preliminary test should be made on each new substrate. Surfaces should be thoroughly cleaned with a suitable hydrocarbon solvent such as mineral spirits, naphtha, MEK, etc. Solvents must be wiped from the surface before GT Products 2100 is applied. GT Products 2100 cures on exposure to the moisture in air. Cure time increases with confinement and cross sectional thickness and decreases with increased humidity and temperature. Curing above 150°F will reduce physical properties. At 77°F and 50% RH GT Products 2100 will skin over and become tack-free in 1020 minutes. Tooling and removal of masking tapes should take place prior to this time. GT Products 2100 should be applied in a less than ¼ inch diameter bead to assure a complete cross section cure. Metal to metal bonds should not overlap more than 1 inch. The odor given off during the cure of GT Products 2100 is acetic acid and disappears when fully cured.
Caution GT Products 2100 is not recommended for use on calcareous surfaces or on materials that bleed oils or plasticisers.
Storage and Shelf Life GT Products 2100 has a shelf life of 12 months when stored in the original unopened containers at or below 90°F.
Health and Safety
GT Products 2100 is sold for industrial use only. Uncured product will irritate the eyes. In case of contact with the eye, flush with running water for 15 minutes and call physician. Uncured GT Products 2100 may also irritate the skin. Removal by wiping with dry cloth or paper followed by washing with soap and water is recommended GT Products 2100 releases acetic acid vapor during cure. Adequate ventilation is required. Wearing contact lenses should be avoided because vapor may be trapped behind the lenses.
The above data is based on typical experience and should not be used for specification writing. Suitability of this product for a specific application should be determined under actual use conditions. No warranty, expressed or implied, is hereby made.
1 Nov. 2002
GT Products inc. 501 Industrial Blvd. Grapevine, TX 76051 Phone # 800-221-0866 Fax # 817-421-1211